Fractal Design Define XL R2 Case Review: Maybe We Can Have It All?by Dustin Sklavos on February 20, 2013 12:01 PM EST
- Posted in
- Fractal Design
Introducing the Fractal Design Define XL R2
Amusingly and appropriately enough, the wave of silence-oriented enclosures that have been popping up recently haven't really drawn attention to themselves as a trend. Yet all of a sudden, we have results from a couple of solid contenders from Nanoxia and a few less expensive (and more readily available) also-rans. For a little while, this was a wave that Fractal Design was riding high, but the Define R4 wound up being a little underwhelming. As it turns out, they might just have something better lying in wait.
We never had a chance to play with the original Fractal Design Define XL, so it's tough to draw a direct comparison there. Yet one look at Fractal Design's page for the original tells you that while the Define R4 didn't change much from the R3, the Define XL R2 is a major shift. The original XL didn't support E-ATX; it was more just a conventional Define with a separate drive compartment. This R2, on the other hand, really is a giant Define R4. As it turns out, that bump in size and modest increase in cooling capacity may very well have been all the Define R4 needed.
There are two dead horses I need to bludgeon before we progress any further with this review. First, the quiet chassis to beat are the Deep Silence 1 and 2 from Nanoxia; availability notwithstanding, those two offer the best value and best balance of performance and acoustics. In the XL R2's price bracket, the Deep Silence 1 is basically the bar. Keep in mind, though, that the DS1 is a smaller case than the XL R2, so if you need the extra space, Fractal Design may just win by default.
The other thing to keep in mind is that designing a quiet chassis is basically one of the hardest things a vendor can do. What you're essentially trying to do is get the system inside the case to a noise level low enough that the sound dampening material can do the rest of the job. High end enthusiast cases tend to be very quiet because of their copious high power, low noise airflow. What we want is a case that can get below that already low noise floor. The problem is that doing so means closing off a lot of ventilation; capturing sound means capturing air, and reduced airflow means reduced thermal performance.
|Fractal Design Define XL R2 Specifications|
|Motherboard Form Factor||Mini-ITX, Micro-ATX, ATX, E-ATX, XL-ATX|
|Drive Bays||External||4x 5.25"|
|Cooling||Front||1x 140mm intake fan (mount supports 120mm; second 120/140mm fan mount below)|
|Rear||1x 140mm exhaust fan (mount supports 120mm)|
|Top||2x 120mm/140mm fan mount|
|Side||1x 120mm/140mm fan mount|
|Bottom||1x 140mm intake fan (mount supports 120mm)|
|I/O Port||2x USB 3.0, 2x USB 2.0, 1x Headphone, 1x Mic|
|Power Supply Size||ATX|
9.13" x 22.01" x 22.04"
232mm x 559mm x 560mm
|Weight||36.16 lbs / 16.4 kg|
Removable fan filter
USB 3.0 via internal header
Three step fan controller supports three fans
Acoustic padding on the interior and side panels
Modular, rotatable drive cages
Consider that the two Deep Silence cases are already pretty heavy and well built in their own right, then add another ten pounds and three inches. The Define XL R2 is made almost entirely of steel with really the bare minimum of plastic used in its construction, and you definitely feel it. This is a big case, but Fractal Design was able to hit a very aggressive price point with it. The last generation Define XL cost a full $40 more.
Post Your CommentPlease log in or sign up to comment.
View All Comments
omgia - Wednesday, February 20, 2013 - linkI moved from a p180 to an Define R4 recently. The most notable difference between this and the p180 is the cable routing. There is a significant difference in the amount of space behind the motherboard for routing cables. Also, my R4 is 4-6 degrees cooler (F) than my Antec P180 was with the supposedly better thermal sections. This may be because these cases uses 140 vs 120mm fans. But also, with the ability to get all of the wires behind the motherboard, you have better airflow. Something I was personally never able to achieve with the P180. I like the build quality of this case better than the P180 as well. Support for front USB 3.0 is also nice. I was thinking about getting a P280, but after completing my build, I have no reservations that the R4 or XL-R2 are better cases.
akhaddd - Wednesday, February 20, 2013 - linkeep Silence cases are already pretty heavy and well built in their own right, then add another ten pounds and three inches. The Define XL R2 is made almost entirely of steel with really the bare minimum of plastic used in its
lwatcdr - Wednesday, February 20, 2013 - linkWith the new closed loop systems from Corsair, NZXT, and Swift tech it would be nice to know which fit in the case. Yes I know you can not test with every Motherboard but they are becoming mainstream so it would be helpful to add that data even if it just "The mounting screws will fit.
omgia - Wednesday, February 20, 2013 - linkI just purchased a Define R4 and one of the biggest problems is reaching the 12V lead up to the top-left of the case.I'm sure most would fit if routed over the top of the motherboard, but you really need a long one to route through the grommets.
One feature of the XL-R2 and the R4's are mounting spaces for SSDs on the back of the motherboard tray. This seems like a great idea at first, but you must mount it prior to installing the motherboard (meaning you'll have to remove the motherboard to remove the drive). And the mounting positions are far enough away from the other drives, it may be difficult to share a power lead between the drive trays and the 2.5" mount points. I was able to share one with a SATA lead with 3 connectors, but not a lead with 2. The center connector on the lead with 3 became useless.
Not sure about the XL-R2, but on the Define R4, the center drive tray is subject to vibration from mechanical drives. Even with the screws on the drive tray holder secured tightly, there were significant vibrations that could easily be heard outside the case. This was evident even using the bottom screw holes with rubber grommets. I had to torque down these screws hard to get the vibrations to stop.
As far as noise goes, these are silent cases, not silencing cases. The foam may help a little, but it is not going to really do any sound deadening. The case on its own is whisper quiet without any components. But I can still hear hard drives chirping and my noisier cpu fan. If you are replacing an existing case, listen to your system without all of your existing case fans running. That is how it will probably sound with an XL-R2 or Define R4. Maybe a decible or two lower, but nothing significant.
Touche - Wednesday, February 20, 2013 - linkIs that GPU crooked?
snakyjake - Wednesday, February 20, 2013 - linkI wanted a large case for a NAS/Multipurpose machine that will be in my home, so need something quiet.
bsix - Wednesday, February 20, 2013 - linkWith the Define (regular size) cases the inlet airflow is stifled because of the drive cages and the more restrictive cages they use. This problem seems so be solved by using the bottom fan. This is really the only difference in these two cases from an airflow perspective.
i bet the R4 would do much better with an additional inlet fan on the bottom and potentially some better case fans that can lower the noise floor an additional 2 db.
This would be really appreciated - I bet the R4 would be equal to both the nanoxia and the XL R2 in acoustics with this setup.
stratosrally - Wednesday, February 20, 2013 - linkI do realize that Anandtech is known for pulling no punches (and am thankful for that!) but the article really doesn't come across positively enough. The fact that it is such a large case, comes with 3 fans & a fan controller, and performs so well for a suggested list price of only $129.99 ought to be given more emphasis in this review.
The review seems to be almost begrudging in admitting that the XL R2 does so well across the board. For example, the amount of room for cable routing (26mm - more than an inch!) precludes the need for channels in the motherboard plate which would just add complexity and cost.
BTW - the constant promotion of the Nanoxia can be a bit frustrating given that it still isn't available in the US. It, too has no motherboard guide post and you mentioned similar issues in installing the PSU. You also mentioned I/O panel & GPU installation issues. You actually stated you might be coming across as nitpicking in that review, yet gave it the Bronze Editor's Choice Award.
I personally think there's a limit to how much reasonably-priced enclosures can ease assembly. I don't mind installing my own standoffs and paying attention (using both hands, etc.) when installing the PSU. Given the variety of motherboard sizes this case will accept you'd quite possibly be adding or subtracting standoffs anyway.
If I wanted everything done for myself I'd expect to pay a more premium price. As this case is larger and performs equal to or better than the Deep Silence 1 in the tests - IMHO it deserves the Silver or even Gold Award.
five_seven - Thursday, February 21, 2013 - linkAfter reading so many reviews I, too, am tired of hearing about stand-offs not being installed on a motherboard. An enthusiast building their own PC is doing just that-- building their own PC. If people really feel dragged out by having to figure out how to align a motherboard with a lack of stand-offs or a center stud, they've got bigger problems.
Rather than docking any points from your " utterly worthless, arbitrary point system" over this issue, might I suggest simply indicating if a case provides stand-offs and if the user will need to install them or not. Some objectivity in regards to this issue, however, would be nice.
UNhooked - Thursday, February 21, 2013 - linkOnce again no watercooling support of any kind was discussed. You really need to start incorporating this. It is now a vital part of case reviews based on mainstream watercooling has become.