Lian Li's PC-6070 Aluminum Case
by Purav Sanghani on March 25, 2004 10:27 PM EST- Posted in
- Cases/Cooling/PSUs
Case Fans
The PC-6070 includes three 80mm fans of its own. Two are mounted at the front of the case directly in front of the drive carriage. These fans serve as intakes and blow outside air directly at the 3-1/2" drive bay carriage to cool installed hard drives. A second option would have been a larger 120mm fan, which would further reduce noise levels. Air is pulled in via a removable vent at the bottom of the case, directly in front of the first pair of stands. A reusable filter is also included.
Click to enlarge.
The third fan is mounted at the rear directly below the PSU opening. This single fan serves as the one and only exhaust for the PC-6070. We noticed that in many other cases, two fans are used to exhaust warm air out of the rear. This imbalance could cause increased temperatures of components, lowering the overall performance. And since there are no other openings on the chassis, additional fans cannot be installed.
Click to enlarge.
The power connectors are standard 4-pin leads with pass-through female leads. This allows the fans to be daisy-chained to other components as well as themselves.
Facebook
Twitter
RSS
19 Comments
View All Comments
puravsanghani - Sunday, March 28, 2004 - link
#13: You're right! We have fixed this typo in the review.#18: I agree, we have been performing the heat tests with the power supply fan ON to simulate a system under normal operating conditions. The fan was only turned off for the noise benchmarks. We will state this in future reviews.
Thanks for all of your input, if you have any other questions feel free to email me at purav.sanghani@anandtech.com
divide_by_zero - Sunday, March 28, 2004 - link
"As mentioned before, Lian Li is well known for its aluminum products and they know how to use the metal alloy."Aluminum is a pure metal, not an alloy. Symbol Al on the periodic table of elements.
On the Design page the link to the Silverstone Nimitz is to the manufacturer's page, not to the review that it refers to - which I'm sure has a link to the manufacturer on it and which I didn't see
"Unlike the SilverStone Nimitz that we reviewed last week"
I can see doing sound tests with the power supply fan off to eliminate it as a variable between cases. But it seems to be implied that the heat tests are also done with the power supply fan off. If this is true then the heat tests do not reflect actual operating conditions.
divide_by_zero - Sunday, March 28, 2004 - link
"The third fan is mounted at the rear directly below the PSU opening. This single fan serves as the one and only exhaust for the PC-6070. We noticed that in many other cases, two fans are used to exhaust warm air out of the rear. This imbalance could cause increased temperatures of components, lowering the overall performance. And since there are no other openings on the chassis, additional fans cannot be installed."I would think that this actually is the correct number of fans to have be *in* balance, since the power supply will also be exhausting air.
ripdude - Saturday, March 27, 2004 - link
Kristopher, could you take the Coolermaster CM Stacker STC-T01 in the roundup if you can lay your hands on one?I'd like to see it tested.
--rip-dude
KristopherKubicki - Saturday, March 27, 2004 - link
Purav and I are working on a roundup. We got a new testbed, A64 with Zalman 7000Cu hsf. We are RETESTING all of these. What fun!Kristopher
Gromis - Friday, March 26, 2004 - link
Hmmm. From a $150 case, I'd have expected rubber grommets mounting for hard drives... after all, it's available in much cheaper units, such as HEC 6A series.Visual - Friday, March 26, 2004 - link
you listed 55dba for the kingwin while in its own review you listed it at 48dba so what's the difference from?LarryHorse - Friday, March 26, 2004 - link
I have this case and Spacecomber there is not much clearance between the heat sink and the power supply. I have a stock AMD heat sink and I get about an inch clearance.My temps range from 39C to 46C on a Barton 2500+ with stock settings. There is room below the back exhaust fan to install an addition fan if so desired.
The case does run very quiet. This can best be heard when reading from an optical drive. Closing the front door almost completely removes the sound of the cd spinning up. This is great if you read or write a lot to a high speed drive.
One or two more fans would have been nice and the case can get a little tight if you run a lot of drives or a larger heat sink, but overall a solid case.
thundershaft - Friday, March 26, 2004 - link
I was on the market for a Lian Li case..I had to choose between the PC6089A or this case.. at the end.. I didn't like the PC-6070 because the lack of air... if u are running a hard-drive and 2 optics.. I think it is the best case around.. anymore than that? NO GOOD...
I trieed it with my 8 drive setup.. TOO HOT INSIDE
BTW.. spacecomber.. there is enough clearance space.. I have tested it with a enermax 565 and it works fine =)
Spacecomber - Friday, March 26, 2004 - link
I liked the write-up and the choice of this case for a review. (I also see that page 3 is now fixed.) One area that I would have liked to have seen a bit more coverage about was how well this case can accomodate oversized heatsinks, such as those made by Zalman and Thermalright. A case like this is aimed at those wanting to build a silent computer, and one way to go about this is to use very large heatsinks and slow rpm fans. However, I'm afraid that this case will have a problem with any heatsink that overhangs the edge of the motherboard. I think this will be a problem with Zalman 7000A heatsinks when the socket is close to the edge of the board and with the Thermalright heatsinks that mount directly to the motherboard on socket A motherboards, if the socket is close to the edge. I see two ways that this could be a problem for this case. First, it will prevent the motherboard tray from sliding completely in or out. Second, there won't be enough clearance between the power supply and heatsink. A picture showing and/or some measurements about how much distance there is from the edge of the motherboard to the edge of the motherboard tray and from the edge of the mothergboard to the bottom of the power supply would be helpful in this regard.Just my 2 cents.
Space